Samsung washers have been becoming pretty popular over the last couple of months. These devices will serve you with long-term performance.
However, you will have to install it properly to avoid issues with the water supply and drainage. The majority of owners prefer to hire general contractors to help with the installation.
So, if you have a bit of cash to spare, try referring to local experts, and they will guide you accordingly.
However, if you’ve installed the unit yourself, you might deal with a situation where the Samsung Aqua Jet VRT washer is not draining all the way.
Luckily, all hope is not lost, and you can go through some basic fixes to address the situation. Just follow through with these details, and your washer will be all set!
Samsung Aqua Jet VRT Washer Not Draining All the Way
- Check Washer Level
You should always start by adjusting the level of your washer. If you’re sure that the position of the washer is a bit slanted, then it might be time to adjust the base with cardboard.
It won’t drain properly until every section is perfectly level.
So, even if the floor might look level to your naked eye, there is no harm in using a level. Nine times out of ten, people find that they are dealing with slanted floors.
So, here you need to fix the orientation of your washer and then test out the unit again.
- Unclog Drain Tube
The drain tube might also be to blame here. If you’ve not cleaned the unit in a while, then make sure to unclog the drain.
Similarly, there might be kinks in the main drainage line, or it might be pitched. So, if you’ve recently moved the unit, make sure to check the drainage system.
This is one of the most common reasons behind the washer not draining all the way. So, make sure to fix the condition of the drainage line for optimal water flow.
Hopefully, you won’t have to worry about anything after that.
- Replace Water Filters
Most of the time, a quick rinse of the water filters is enough to keep everything working.
If you’re sure that the washer is level and the drainage system is not clogged, you just have to replace the filters. There is no point in working with clogged filters that have been rinsed out multiple times.
However, while you wait for the new filters to arrive, you can wash the current filters one more time. That should improve the drainage situation with the unit.
Be sure to switch to new filters as soon as possible after testing out the current ones for a few days.
- Tilt Your Washer
Sometimes, your washer needs a bit of slope to get all the water out. Even if you’re sure that the washer is level, a bit of residue will be left inside the washer.
To address this situation, you have to tilt the washer slightly.
Just use some small wooden blocks to tilt the washer towards the drainage line. However, slanting the washer too much will create problems with the spinning mechanism.
So, make sure to use a small block that won’t elevate your washer too much.
Similarly, it is a good idea to clean the inside of your washer to free up the drainage holes. While it is pretty rare for these holes to get clogged, it can still happen.
This is especially true if you’ve not used the washer in a few weeks. So, make sure to use water pressure to free up these holes.
- Check For Damaged Sections
If you’ve had the washer for a while, it is a good idea to inspect the whole unit for kinks and damaged sections.
The warranty is valid for a few years if you’ve bought this unit from an authentic dealer. So, reach out to the customer care professionals, and they will guide you accordingly.
Your main focus should be on finding leaking sections and rusted lines. If the issue is genuine, the warranty should cover this error.
So, contact the official healer, and he will handle the rest.
- Distribute Load
The issue might also be with the load. If you’re using a heavier load without any fluff or in the washer, the drainage system won’t be able to work properly.
To address this situation, you need to add some towels or pillow covers to evenly distribute the load.
Following this technique will not only help you with the drainage cycle, but you will also notice a better cleaning performance.
So, make sure to add some pillow covers, sheets, or towels, even if they are clean.
- Start A New Cleaning Cycle
This problem with the Samsung Aqua Jet VRT washer can also be linked to the programming side of things. If you’ve yet to start a cleaning cycle, engage the system one more time.
Chances are that there are no serious issues with the device. So, just remove power from the unit for a few minutes.
After waiting for around 10 minutes, you can power up everything and put in a new load to test out the machine.
If everything is in perfect order, you won’t have to worry about drainage issues here.
- Get Help From Samsung Support
Samsung support team is one of the most responsive services on the market.
If you don’t want to spend more time trying to isolate the issue yourself, just reach out to these professionals. They will guide you through each step of the troubleshooting process.
Moreover, it becomes pretty easy to isolate the issue when you’re getting help from an expert.
So, keep that in mind if you can’t seem to narrow down the errors with the Samsung washer.
Overall, the majority of issues with the unit can be linked to the faulty installation of the unit. So, if you want to avoid these errors, try hiring a local contractor. He will take care of all the drainage and wiring connections for you.
You just have to extend your budget by a small margin and enjoy the amazing performance of the Samsung Aqua VRT Washer.