Cleaning is a process that involves work, labor, and patience. This work labor can be minimized by using Ecovacs Deebot devices.
Spending money on a cleaning robot might seem a bit extensive at first, but you’ll surely get amazing performance and efficiency from these systems.
The setup is fairly simple when you’re using options like a Deebot or a Roomba for your home.
However, there are still some basic maintenance needs that you have to track to get optimum response from the system. Managing these stems can get a bit hard at times if you’re not aware of the proper care.
Ecovacs Deebot offers a robotic vacuum and mop cleaning system, which cleans very efficiently and thoroughly, reducing time and labor.
These products come in handy, especially when you find tasks such as cleaning to be chores.
However, some issues are likely to appear when you handle such devices. That being said, a common system error that users have reported is the Ecovacs Deebot LDS malfunction.
If you run into a problem of such nature, this article will explain all the necessary steps required to resolve LDS malfunctioning.
How to Fix Ecovacs Deebot LDS Malfunction?
- Inspecting the problem:
The first step to take, whether you encounter a certain bug in the device, is to inspect the problem.
This procedure will accommodate recognizing the nature of the issue. It is not likely that every time the device starts malfunctioning, the Laser sensor is the cause.
It may be a cause of power failure or improper use of the product. Hence, examining where the issue lies should be done firsthand after running into a problem.
- Cleaning sensor:
After inspecting the problem, if it is confirmed that the laser sensor is malfunctioning, then you need to perform certain actions on the sensor to make it work again.
A laser sensor is a very sensitive but important device that uses AI laser to clean and mop specified areas. It is most probable that if the sensor is nonfunctional, it may be a result of debris or dust accumulated on the sensor.
- Tapping the sensor:
In the case of a nonfunctional laser sensor, Tapping the sensor of the laser or cleaning it with a clean cotton swab will eventually get rid of any debris or dust layer that is stuck on the sensor.
Washing is not recommended for the highly sensitive and efficient sensor as it can damage the layers of the laser, making it useless.
Hence, it is a careful process. Any unwanted force might cause potential harm to the sensor resulting in breaking the laser. So, this process should be done with care.
- Empty Dustbin
Sometimes, all that you will need to do is to empty out the dustbin and then check on the response from the sensors one more time.
It is not that rare for the debris from the dustbin to clog up the sensors, and you might be dealing with the same situation.
The only thing that you can do here is to get the dustbin out, clean the compartment as well as the dustbin itself, and then place it all together again. That will be more than enough to help you fix the issues with the clogged sensors.
One thing to keep in mind is that you can rely on canned air to get rid of the lodged debris. From there, you can insert the bin back into the unit slowly.
That will not create more errors with the system, and you will notice a better response from the unit.
It all comes down to keeping the sensors clean, and you’re not left with other methods. So, be sure to keep that in mind and follow through with the basic maintenance of the system.
Hopefully, the seniors will be in good shape, and you will not have to go through extensive maintenance cycles.
- Leave The Unit To Charge For A Few More Hours
The issue can also be linked to the charging status of the unit. If you’re sure that the system is perfectly clean and there are no issues with the debris lodged on the sensors, then you need to check the power status in the system.
You can’t expect the cleaning robot to perform when the battery is not supplying the system with enough power. So, the first thing that you can do to isolate this error is to leave the unit out to charge for a few more hours.
From there, you can engage the cleaning cycle one more time and then check up on the LDS malfunction. Nine times out of ten, your issue will be fixed, and you will not have to bother with more errors down the road.
The same statement is true for a defective battery pack, as the battery life can vary from unit to unit. Your storage and operating conditions will play a huge role here, and you will have to get a replacement to get ahead of these errors.
To further confirm the issue, you can engage the battery pack with a multimeter and then check on the response from the system one more time. If you find the voltage supply from the pack to be limited, then you need to get a new battery.
- Place On A Level Floor
Depending upon the model of the Deebot system you’ve purchased, it will only work with hardwood floors.
If there are too many rough patches on the floor or the floor is not level with bumps across the sections, then you need to get a replacement.
You can’t expect this system to perform in poor conditions and will have to struggle with more errors down the road.
So, be sure to keep that in mind and test out the performance on a stable patch. If you do get a response from the LDS components, then you’ll know for sure that the floor is to blame.
There is not much that you can do here for the robot. Instead, you need to focus more on repairing the floor and maintaining a stable level to avoid a hassle down the road. Similarly, you will have to check the base for damage.
There is always a possibility that the unit is damaged, and you won’t be able to fix it yourself with any quick methods or troubleshooting routine. So, be sure to reach out to a professional and get it checked.
- Getting it Checked /Repaired:
In most cases, cleaning a sensor would do the work of resolving the issue. Just in case, if the laser is still nonfunctional, it might be the subject of a faulty or broken laser sensor.
This rarely happens in Deebot products, but it is important to get it checked by a repairer. If any fault in the sensor is observed, the sensor should be changed, or you can ask the company to send in another device as a replacement.
In case your device is out of warranty, we’re afraid that you will have to replace the device by purchasing a new unit. Unfortunately, doing so should cost you quite a few bucks.
- Referring to customer care:
Technical faults in a smart appliance are normal yet unpredictable. So, it is always the best option to contact the customer care center for any inconvenience regarding their product.
A professional hand in analyzing the nature of the problem is highly recommended as it may prevent the device from unnecessary damage and repair procedures.
They will provide the best possible solution for the related issue without worrying about inspecting the problem.
Though, do make sure that you are as cooperative as you possibly can when you are addressing the issue. Similarly, they should be able to advise further solutions to the problem.
Though If the laser sensor still does not work, it is advisable for the user to change the product and purchase a new one, as that might be the only option left.
The Bottom Line:
Is the laser sensor not working.? It may be a problem of accumulation of dust and debris over the sensor, which makes it nonfunctional.
The above-mentioned steps in this article will help in troubleshooting the problem. So, if you run into an LDS malfunctioning, you know what steps to take in order to solve the issue.
Nine times out of ten, you’re just missing the basic maintenance of the unit. You need to focus on keeping the sensors clean.
A bit of maintenance will go a long way when you’re dealing with these smart devices. Even the most amazing brands, like Ecovacs, can malfunction if you keep ignoring these systems.
So, be mindful of the unit’s maintenance, and it will be much easier to figure out the issue.
You can also reach out to the dealer about the basic maintenance needs of the unit. He will guide you on how to keep the device in perfect condition without having to worry about any errors down the road.
So, be sure to reach out, as you’ll avoid a ton of hassle that way.